Skip to content

Alumina ceramics

Alumina ceramics

A starting point for electrical insulation, wear components and structural parts.

Illustration of alumina ceramic coupons beside a copper busbar

Start with the application

Compare the required purity, surface condition, environment and mechanical load. Material family alone does not define the performance of a finished part.

What to specify

Material designation
Al₂O₃
Grade & performance
Use the actual supplier datasheet and test conditions; no numerical values are asserted in this preview.
Finished component
Define dimensions, critical features, finish and acceptance criteria on the agreed drawing.
MATERIAL SELECTION

Material performance

Six-axis performance profile

  • 1 Limited
  • 2 Moderate
  • 3 Strength

Bands run from the center outward. Unrated axes have no marker.

  1. HardnessStrength

    F99.7 is listed at 17.3 GPa under HV10 in the KYOCERA catalog as a calculated value. Its individual data sheet reports HV1.0.

    KYOCERA ceramic data sheets
  2. Wear resistanceStrength

    KYOCERA identifies dense F99.7 as wear-resistant for matched pistons and cylinders, bearings and valve parts. Check the contact pair and wear mode.

    KYOCERA oxide ceramics applications
  3. High-temp strengthModerate

    For family screening, KYOCERA measured 350 MPa at 1,000 °C in four-point bending for alumina AO480S. Obtain hot-strength data for F99.7 for the actual load.

    KYOCERA four-point bending at temperature
  4. Thermal shockModerate

    F99.7 has a reported 180 °C temperature difference in a DIN EN 820-3 Type A water test. Apply the result within that test context.

    KYOCERA F99.7 data sheet
  5. Thermal conductivityModerate

    F99.7 is 34.9 W/(m·K) at 20 °C and 6.8 W/(m·K) at 1,000 °C in the grade sheet.

    KYOCERA F99.7 data sheet
  6. Corrosion / chemicalStrength

    KYOCERA rates F99.7 resistant to 5% and 10% acetic acid at room temperature and boiling. Check your specific medium, concentration and temperature.

    KYOCERA oxide ceramics corrosion tables
How the bands are assigned

The bands are for initial material selection. For published HV10 hardness, the cutoffs are 10 and 15 GPa. For thermal conductivity, they are 10 and 100 W/(m·K). On the other axes, the bands reflect suitability in the applications and test conditions described alongside each property. Check the actual grade and operating conditions for your project.

Material selection reference data

Al₂O₃ · KYOCERA · F99.7

The values below apply to the cited manufacturer and grade. A dash means no comparable value was available in the cited source.

PropertyReference value
Hardness (HV10, GPa)17.3DIN EN ISO 14705, Procedure A (converted by KYOCERA).
Thermal conductivity (W/m·K)34.9DIN EN ISO 18755.
Thermal shock coefficient (R₁, K)—

Hardness testing standards for oxide and non-oxide ceramics differ. Compare values only when the method and test conditions match.

KYOCERA ceramic data sheets

Specifying the insulation surface

Use the illustrations to identify the faces, edges and surface finish to call out on your drawing. Include the electrical duty and mating parts.

Before you enquire

What should I include in a ceramic part enquiry?
Start with a drawing reference, material preference, quantity, working conditions and critical dimensions. If the grade is open, describe the function and constraints first.
Can I start without a complete drawing?
Yes, the enquiry can start from a functional brief. Final feasibility, dimensions and acceptance criteria still need to be agreed before an order.
What do the custom component examples show?
The examples show shapes and material families from previous custom projects. Jiwei confirms the grade, dimensions, tolerances and acceptance criteria for each new drawing and operating environment.

Related custom component examples

Discuss your material and drawing

Describe the function, quantity and any critical requirements.

Request a quote

Surface finish and edge preparation

Illustration of a ground alumina surface and chamfered edge